TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT Process) certain hazardous substances in electrical and electronic equipment. C Lot No. . this document, the specifications, the data sheets and application notes. CY Bipolar Transistors – BJT are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for CY Bipolar Transistors – BJT. COR NTE Equvilent NTE31 TRANSISTOR NPN SILICON V 1AMP GIANT TO CASE TV SOUND OUTPUT COMP’L TO NTE NTE Data Sheet.

Author: Zukus Gardagar
Country: Pakistan
Language: English (Spanish)
Genre: Software
Published (Last): 13 January 2016
Pages: 316
PDF File Size: 15.52 Mb
ePub File Size: 4.8 Mb
ISBN: 572-2-45636-470-4
Downloads: 98827
Price: Free* [*Free Regsitration Required]
Uploader: Goltizilkree

I stand by my assesment of Shocwaver’s requirements for a switching transistor eatasheet as in another thread on a similar subject. Your name or email address: It’s the voltage given from the pins of a PC parallel port and this voltage changes depending on the load it’s driving, so i guess the right question for the base should be: Then you can saturate the transistor however much you want e.

Do you already have an account? We don’t know if the 5V signal is still 5V when loaded.


Mar 2, 5. I have a 12V power supply and a square wave V as a input on the base.

Posted by datasheer in forum: Or even as I tried from beginning 4. My input signal is traneistor particular: Mar 2, 4. V CEO V. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook.

Solar Powered Security Light In this teardown, we will look at the internals of a motion-activated light which contains its own solar charging system. Unintended Usage include atomic energy control instruments, airplane or. Since the diode voltage of the base-emitter junction is generally about 0. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.


Is “R1” the base resistor? The transistor can also be checked by removing it from the circuit and using an ohm-meter: This is how I envisioned the circuit: If you don’t care whether the load you’re driving is sinking mA or mA, and it’s only important that it doesn’t exceed a maximum of mA, ttransistor choose R2 such that no more than mA can flow through it.

Mar 2, 3 0.

Micro Commercial Components 2SCO, 2SCR, 2SCY datasheet pdf

The resistor can be checked by removing it from the circuit and using an ohm-meter. No, create an account now. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. Without a schematic, “R1” and “R2” are meaningless labels.

I’m burning my brain. Mar 3, 9. Mar 3, Yes, my password is: The attached simulation diagram “sim” shows a circuit using the values I derived, the results are in the “res” file and “zoom” shows the low output relative to ground a few tenths of a volt as should be expected. Infrared Capabilities Remote controls for electronics often use IR infrared radiation in a very precisely coded sequence for channel surfing, volume adjustments, and more. V CBO V. May 16, 5, 8. I guess I attempted to establish what he was talking about in my first response.

Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances.

C2383 Datasheet PDF

You May Also Like: Quote of the day. Please use these products in this document in compliance with all applicable laws and regulations. No license is granted by implication or otherwise under any patents or other rights of. I am checking with my tester and there is never current through R1 voltage between sides of it it’s always 0 no matter the input, so i wander how can the current reach the base??


I’m starting to think that this bjt is burned.

The bjt is of course in common emitter configuration. If you’re using the transistor purely as a switch, that means you want to saturate the output, or try to cause more current to flow from collector to emitter than your current limiting resistor will allow.

It is the responsibility of the buyer, when utilizing TOSHIBA products, transistir comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property.

Mar 2, 2.

C Hoja de datos ( Datasheet PDF ) – 2SC

How can i calculate the resistor between the input and the base and the resistor between supply and collector? Using continuously under heavy loads e. It is very unlikely that the resistor is bad – they typically get fat and brown when they open. Then a darlington driver transistor must replace the ordinary transistor. Similar to what veritas has explained:

Author: admin