Interzinc B. Storage Conditions: All painting materials shall be stored in a clean, dry, well ventilated place, protected from sparks, flame. A three component, metallic, zinc rich epoxy primer which passes Slip B coefficient. Interzinc B complies with SSPC Paint 20 and contains minimum 80%. Interzinc Call for Price. A two component high solids, low VOC metallic zinc- rich epoxy primer formulated on proprietary polymer technology which provides.
|Published (Last):||19 February 2006|
|PDF File Size:||17.94 Mb|
|ePub File Size:||2.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
Temporary protection and heat shall be maintained at this minimum temperature for 24 hours before, during and 24 hours after material application.
Areas will be designated by the Architect. Submit plan, section, elevation and perspective drawings as necessary to depict system configuration, design considerations and application procedures. Steel substrate temperature shall be a minimum of 5 deg F 3 deg C above the dew point of the surrounding air for a period of 24 hours prior and during the application of the material. The Manufacturer’s quality management system must be assessed and registered by an independent registrar as conforming to the requirements of ISO This section inherzinc based on the products of International Protective Coatings, which is located at:.
Provide ventilation in areas to receive work of this section during application interzijc minimum 24 hours ibterzinc application.
Clean substrate free of dust, dirt, grease or other foreign substances that would impair the bond of the coating. Protect work area from windblown dust and rain.
Interzinc | Litnobiles
Information must demonstrate equivalence of product and performance to the specified material and complete systems. Once agreed upon in writing it serves as a guide for the finished work. Pipes, ducts, conduits, hangers and supports, equipment, and equipment enclosures exposed to weather or view – intetzinc finish.
Delete the next paragraph if not applicable. Mild Atmosphere Interzijc Urban and industrial atmospheres. Coordinate with Section and Contract Drawings for all Moderate Atmosphere areas of the project. Moderate sulpher diuoxide levels.
Company specializing in applying the work of this section with a minimum of three 3 years documented experience and certified by the manufacturer. Apply approved primer to properly cleaned substrate in accordance with manufacturer’s application instructions.
A copy of the transport document and manufacturers conformance certificate shall be attached to the material delivery QC form. When deciding on the extent of the mock-up, consider all the major different types of work on the project.
Pipes, ducts, conduits, hangers and supports, equipment, and equipment enclosures exposed to view in all rooms and spaces.
Upon completion of installation, all excess material, overspray and debris must be cleared and removed from the job site. All surfaces to receive coatings must be clean, dry and free of oil, grease, loose mill scale, dirt, dust or other foreign substances which would impair bond of the material to the substrate. Submit manufacturer’s written installation instructions.
At project closeout, provide to Owner or Owners Representative an executed copy of the manufacturer’s standard limited warranty against manufacturing defect, outlining its terms, conditions, and exclusions from coverage. Do not apply coatings under environmental conditions outside manufacturer’s absolute limits.
Do not commence adjacent or adjoining Work until the application of the coatings is complete in that area. All products listed in this section must be manufactured under the appropriate follow-up service with each container bearing the certified label mark.
Sequence and coordinate application of coatings with Work in other sections which would interfere with efficient protective coating application.
Moderate Atmosphere Applications – Industrial and coastal areas. Pipes, ducts, conduits, hangers and supports, equipment, and equipment enclosures exposed to view in all interzicn and spaces except mechanical rooms, electrical rooms, and utility rooms. If necessary for job schedule, the General Contractor shall provide enclosures and heat to maintain proper temperatures and humidity levels in inherzinc application areas.
Provide primer cut back areas a minimum three 3 inches 76mm from bolted connections and minimum twelve 12 inches mm from welded connections.
Verify that substrate and workspace temperature and humidity conditions intrezinc in accordance with requirements of this section. Substrate and air temperature shall be in accordance with the manufacturers requirements. Marine, offshore and coastal areas with high salinity. Apply finish coat in accordance with the manufacturer’s application instructions.
Interzinc – A k i r a
Protect adjacent areas from over spray of coating material. Low Atmosphere or Interior Applications – Rural area, low pollution, dry environments. Wood, plaster, concrete, concrete masonry walls, ceilings, soffits, walkways, curbs, steps. Where necessary, cleaning or other corrections of the surfaces to receive coatings are the responsibility of the installer of the incompatible substrate.
Primer applied off site must be in accordance with the provisions of Section The relative humidity of the application area shall not exceed a maximum of 85 percent for 24 hours prior, during and intfrzinc hours after the application of the material.